- #Linksys wusb100 v2 type network security key serial
- #Linksys wusb100 v2 type network security key driver
- #Linksys wusb100 v2 type network security key password
- #Linksys wusb100 v2 type network security key mac
To thwart any unauthorized changes, customize the device’s password so it will be hard to guess. Hackers know these defaults and may try to use them to access your wireless device and change your network settings. These devices have a default password set by the factory. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.įor wireless products such as access points, routers, and gateways, you will be asked for a password when you want to change their settings. Linksys wireless products use linksys as the default wireless network name. This is the name of your wireless network, and can be up to 32 characters in length. Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. Change the default wireless network name or SSID Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.ġ. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Īvis de non-responsabilité concernant les appareils sans fil. Other brands and product names are trademarks or registered trademarks of their respective holders.Īdditional Security Tips. Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. If you use an older web browser, you may have to add in front of the web address.
Website addresses in this document are listed without in front of the address because most current web browsers do not require it. WEB: This globe icon indicates a noteworthy website address or e-mail address. WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product. NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product. To make VAPs work, it is recommended to manually set the macaddr for each wifi-iface section of your /etc/config/wirelessĮ.g.While reading through the User Guide you may see various icons that call attention to specific items. This then leaves you only with even digits for the second digit of the address (i.e.
#Linksys wusb100 v2 type network security key mac
Keep in mind that the MAC address should be unicast (not multicast) or hostapd will not start the interface. You should set the locally administered bit for the MAC address, and then freely set any final digit.
#Linksys wusb100 v2 type network security key driver
The driver rejects any packets from interfaces which are not within a mask (FD:FF:FF:FF:FF:F0) of the main interface (primary AP or STA). But the marker may have been manually toggled, or auto-toggled after three failures. That boot marker switch (A–>B or B–>A) happens at every sysupgrade, so likely you just have the previously used firmware there (either OEM or OpenWrt). It has the contents and settings that were there when the boot was switched last time, usually at the last sysupgrade. Note that there is no guarantee that the other partition works. Thus, if you interrupt the boot process three times, the router thinks that the current firmware is faulty and falls back to to the “known good” in the other partition. If the counter reaches 3, the boot is considered permant-failure and the boot partition marker is switched to the other partition (A–>B or B–>A). And the the counter is reset to 0 at the end of a successful boot. The counter is increased early at the start of each boot process. It should now be booted to the alternate firmware partition ( partitions)
#Linksys wusb100 v2 type network security key serial
Serial 13J2 OEM Firmware Name: cobra.img